Measurement Information
Pleated Blind products may be prepared specially according to measurements reported by customer. Fabric cutting and profile shaping are made taking order record as basis. Wrong measurements may directly affect product fit. Cut materials may not be evaluable in other projects. Careful verification of every measurement before production starts is in customer's interest. This information explains measurement, control, responsibility and support principles.
1. Purpose and Scope of the Information
This text explains measurement rules in pleated blind orders. The information covers window, door and glass balcony applications. Every area may carry different technical conditions. Surfaces with the same appearance may not be equal.
Measurement transaction is not just about writing width and height. Mounting area, profile structure and movement distance must be evaluated together. Gasket, handle and hinge positions must be examined. Every panel must be measured separately.
| Term | Description | Application Equivalent |
|---|---|---|
| Measurement | Width and height values taken as basis in production | Product sizing |
| Panel | Glass or frame section that must be evaluated separately | Independent measurement record |
| Mounting Area | Surface where the product will be fixed | Profile, wall, glass or frame |
| Technical Record | Measurements and selections declared during order | Basis of production order |
| Professional Measurement | Discovery service planned by Pleated Blind | On-site measurement and suitability evaluation |
2. Why Is Correct Measurement Needed?
Pleated blind systems are not ready-measured shelf products. Every order is prepared for a specific usage area. Fabric is cut at the relevant width. Profiles are shaped according to the selected height.
Wrong measurement may cause the product to jam. Missing value may create edge gap. Excessive height may lead to movement problem. Wrong count notification may change delivery plan.
Effect of Measurement on Production
| Measurement Element | Transaction in Production | Possible Result of Wrong Value |
|---|---|---|
| Width | Horizontal size of fabric and profile is determined. | Jamming or gap may arise. |
| Height | Vertical structure is prepared according to order. | Product may not fully cover the surface. |
| Count | Number of parts to be produced is determined. | Missing or excess product may be prepared. |
| Mounting Type | Application components are selected. | Wrong accessory may be used. |
| Surface Information | Fixing method is evaluated. | Alternative solution may be needed. |
3. Preparation Before Measurement
Application area must be made accessible before measurement. Curtain, decoration product or item blocking movement must be removed. Frame surface must be examined visually. Old silicone residues must be taken into account.
Use of a tape measure with metal strip is recommended. Stretching measurement tools may cause error. Values must be noted directly. Memory must not be trusted.
Required Tools
- Tape measure with metal strip
- Note paper or digital recording area
- Pencil
- Phone camera
- Small ladder if necessary
- Panel numbering label
- Adequate lighting
What to Check Before Starting
- Make the application area fully visible.
- Number every panel separately.
- Separate width and height areas.
- Photograph the mounting surface.
- Examine handles, hinges and gaskets.
- Note curvatures if any.
- Determine measurement unit as centimeter.
4. Measurement Unit and Writing Format
In Pleated Blind orders, measurements must be entered in centimeters. Decimal values must be written clearly. Use of comma or dot must be consistent. Values sent without unit specified may be confirmed additionally.
Measurements taken in millimeters must be correctly converted to centimeters. For example, the value of 975 millimeters is 97.5 centimeters. In case of confusion, consult the support team. Unit information must be clear.
| Measurement Format | Correct Writing Example | Description |
|---|---|---|
| Full Centimeter | 75 cm | Value without decimal |
| Decimal Centimeter | 75.5 cm | Half-centimeter value |
| Value Converted from Millimeters | 97.5 cm | Centimeter equivalent of 975 mm value |
| Width and Height | 75 × 135 cm | First value is width. |
| Multiple Order | 75 × 135 cm — 4 pieces | Count must be specified additionally. |
5. How to Take Width Measurement?
Width is the horizontal distance of the area where the product will be applied. Measurement must not be made from only one point. Top, middle and bottom sections must be checked separately. Limited differences may be seen in the areas.
Determination of the most suitable value may vary according to system type. For this reason, no automatic deduction must be made on the measurement. No margin must be added. If technical guidance is needed, receive support.
Width Check Table
| Measurement Point | Value to Enter | Check Note |
|---|---|---|
| Top Section | [CM] | Profile start points must be compared. |
| Middle Section | [CM] | Surface curvature must be checked. |
| Bottom Section | [CM] | Base structure must be examined. |
| Technical Note | [DESCRIPTION] | If there is difference, must be notified to support team. |
Common Errors in Width Measurement
- Measuring only the middle point
- Holding the tape measure at an angle
- Wrongly evaluating gasket margin
- Missing handle protrusion
- Not writing panel number
- Applying deduction by own decision
- Entering different unit as centimeters
6. How to Take Height Measurement?
Height is the vertical distance of the area where the product will be applied. Right, middle and left sections must be measured separately. Frame curvature may affect the result. Base structure must also be examined.
During measurement, tape must be held straight. Folding strip may give erroneous value. Height information must be written clearly. Must not be confused with width.
Height Check Table
| Measurement Point | Value to Enter | Check Note |
|---|---|---|
| Right Section | [CM] | Hinge or handle distance must be examined. |
| Middle Section | [CM] | Vertical curvature must be reviewed. |
| Left Section | [CM] | Profile limits must be checked. |
| Technical Note | [DESCRIPTION] | If there is value difference, photo must be sent. |
7. Glass Balcony Measurement
In glass balcony systems, every panel must be evaluated separately. Measurements may differ even if panels look the same. Rail structure and opening direction must be taken into account. Handle or lock areas must also be examined.
Measurement of one panel must not be copied to other surfaces. Every glass section must be recorded independently. Photos must be matched with panel numbers. Serial production assumption may cause measurement error.
Glass Balcony Record Table
| Panel Number | Width | Height | Opening Direction | Handle or Lock Status | Note |
|---|---|---|---|---|---|
| Panel 1 | [CM] | [CM] | [RIGHT / LEFT / FIXED] | [YES / NO] | [DESCRIPTION] |
| Panel 2 | [CM] | [CM] | [RIGHT / LEFT / FIXED] | [YES / NO] | [DESCRIPTION] |
| Panel 3 | [CM] | [CM] | [RIGHT / LEFT / FIXED] | [YES / NO] | [DESCRIPTION] |
| Panel 4 | [CM] | [CM] | [RIGHT / LEFT / FIXED] | [YES / NO] | [DESCRIPTION] |
Elements to Check in Glass Balconies
- Panel count
- Separate width of every panel
- Different height of every section
- Rail system
- Opening direction
- Handle protrusion
- Lock area
- Gasket thickness
- Profile surface
- Movement distance
8. Window and Door Measurement
Window and door measurements must be recorded separately. Sash widths may differ. Handle position may narrow the application area. Hinge distance may affect movement area.
Bottom section must be examined carefully in doors. Threshold structure may change mounting method. Baseboard or wall protrusion must also be evaluated. Photo support may be requested.
| Application Area | Width | Height | Handle Position | Threshold Status | Note |
|---|---|---|---|---|---|
| Window 1 | [CM] | [CM] | [RIGHT / LEFT] | [YES / NO] | [DESCRIPTION] |
| Door 1 | [CM] | [CM] | [RIGHT / LEFT] | [YES / NO] | [DESCRIPTION] |
9. Measurement According to Mounting Type
Mounting method may affect measurement format. Screwed systems require fixing area. Adhesive solutions need suitable surface. Technical evaluation may be needed in special architectural areas.
Customer must check the method they selected before ordering. If surface is not suitable, alternative may be offered. Wrong application selection may create extra expense. Mounting preference must be thought together with measurement.
| Mounting Type | Element to Pay Attention to in Measurement | Possible Risk |
|---|---|---|
| Screwed Mounting | Fixing area and profile durability | Insufficient surface may affect connection. |
| Adhesive Mounting | Clean, dry and suitable surface | Moisture or coating may reduce adhesion. |
| Special Profile | Architectural protrusion and movement area | Additional part may be needed. |
| Motorized System | Energy point and connection distance | Additional technical preparation may be needed. |
10. Photo and Video Submission
Photo submission may increase the accuracy of technical evaluation. Visuals must show the application area clearly. Close-up and general appearance must be shared together. Measurement points must be visible.
Video record may be useful in moving systems. Opening direction of glass balcony panels may be shown. Handle and hinge areas may also be recorded separately. Visuals must be matched with order number.
Visuals Recommended to Be Sent
- Take the general appearance of the application area.
- Photograph the width measurement point.
- Record the height value visibly.
- Show the handle and hinge areas.
- Display the rail structure if any.
- Take the profile surface in close-up.
- Specify panel numbers separately.
- Send the visuals with order number.
11. Measurements Taken by Customer
Customer is responsible for the accuracy of measurements they report. Production order may be opened over approved values. Incompatibility arising due to wrong measurement is examined separately. This situation is not always counted as production fault.
Pleated Blind may check the submitted measurements from a logical perspective. This review does not replace professional discovery. Confirmation may be requested for clear contradictions. Making a check does not automatically transfer measurement responsibility to seller.
| Situation | Basic Record | Possible Evaluation |
|---|---|---|
| Customer Measurement | Values approved in order form | Declared measurements are the basis. |
| Measurement Sent via WhatsApp | Written message record | Last confirmed value is taken into account. |
| Measurement Said in Phone Call | Written confirmation if any | Written verification may be requested. |
| Third-Party Measurement | Record transmitted by customer | Third-party responsibility may be examined separately. |
12. Professional Measurement Service
Professional measurement service may be offered in certain regions. Service scope is evaluated over address. Discovery fee may be notified separately. Appointment is finalized with written confirmation.
Accessible areas are examined during on-site measurement. Hidden installations may not be evaluated additionally. Renovations made later may invalidate records. Changes must be notified without delay.
Changes That Must Be Notified After Professional Measurement
- Frame change
- Glass balcony renovation
- New silicone application
- Profile addition
- Wall coating
- Painting transaction
- Furniture placement change
- Electricity line arrangement
- Mounting surface being damaged
13. Measurement Approval and Production Order
Order summary must be checked before production starts. Measurements, counts and system preferences must be re-examined. After approval, materials may be allocated to the order. Fabric cutting may be started.
Cut fabrics may not fit other customers' measurements. Prepared profiles may not be usable in different areas. Resale possibility may remain limited. Approval record is decisive.
| Stage | Transaction Made | Correction Possibility |
|---|---|---|
| Before Order | Measurements are entered by customer. | Change may be made. |
| Final Check | Order summary is examined. | Correction may be requested. |
| Production Order | Materials are allocated to the order. | Technical review may be needed. |
| Fabric Cutting | Preparation is made according to custom measurement. | Change may be limited. |
| Profile Process | Sizing is completed. | Re-production may be needed. |
14. Evaluation in Case of Wrong Measurement
In case of wrong measurement notification, order records are examined. Who took the measurement is determined. Written confirmations are compared. Photos may also be evaluated.
Customer-sourced errors may not produce free re-production right. If new product is needed, separate pricing may be made. Evaluation of suitable parts may be examined. If technical solution is possible, offer may be presented.
Wrong Measurement Review Table
| Situation | Review Basis | Possible Result |
|---|---|---|
| Customer-Sourced Wrong Measurement | Approved order record | New production may be charged additionally. |
| Pleated Blind Measurement Record | Discovery form and technical notes | Evaluation is made according to service scope. |
| Renovation Made Later | Visuals before and after measurement | New discovery may be needed. |
| Production-Sourced Incompatibility | Technical production records | Legal rights are evaluated separately. |
15. Custom Production Nature and Withdrawal Right
Pleated blind products may be prepared according to customer's personal needs. Measurement, color and profile selections are specific to the order. Cutting transactions may reduce resale possibility. Profile sizes may not fit other areas.
Products prepared according to measurement are evaluated additionally within the scope of current legislation. Withdrawal right exception may come up. Ready products may carry different provisions. Legal rights arising from defective goods are reserved.
| Product Status | General Approach | Review Criterion |
|---|---|---|
| Standard Ready Product | General withdrawal provisions may be applied. | Product nature and delivery date are examined. |
| Fabric Cut According to Measurement | Custom production exception may be evaluated. | Cutting record and measurements are compared. |
| Profile Prepared According to Order | Personalization nature may be examined. | Profile sizes and production order are checked. |
| Defective Product | Consumer's legal rights are reserved. | Technical review is made. |
16. Separation of Defective Goods and Production Error
Customer measurement and production error must be separated from each other. Product may have been prepared suitable for approved measurements. Fit problem may arise from wrong declaration. Every case is examined with concrete records.
Products prepared differently from production order are evaluated additionally. Missing part notification is examined. Technical faults are recorded. Consumer's elective rights are preserved.
Information Needed for Technical Review
- Order number
- Delivery date
- Approved measurements
- Product's actual measurements
- Photos of application area
- Video record if any
- Mounting information
- Brief description of request
- Contact information
17. Final Check List Before Order
Check before payment reduces measurement error risk. Order summary must be examined carefully. Every panel must be visible in separate row. Count information must also be verified.
- Check the number of every panel.
- Re-read width values.
- Compare height records.
- Verify decimal values.
- Examine the measurement unit.
- Count the product counts.
- Check the fabric selection.
- Verify the profile color.
- Examine the mounting method.
- Add technical notes if any.
- Match the photos with panel numbers.
- Approve the order summary.
18. Creating Measurement Support Request
If there is doubt about measurement, support must be received before production. Photo and video submission may facilitate technical evaluation. Questions must be transmitted in writing. Order number must be specified.
Phone calls may carry general information purpose. Final measurements must be recorded with written confirmation. Social media messages may not count as official order approval. Email or WhatsApp record must be preferred.
Information That Can Be Shared in Support Request
- Name and surname
- Phone number
- Order number
- Application area type
- Panel count
- Measurement table
- General appearance photo
- Close-up visuals
- Video record if any
- Brief description of technical problem
19. Contact Information
| Channel | Information | Purpose of Use |
|---|---|---|
| Company / Brand | Pleated Blind | Measurement, order and support processes |
| Phone | +90 540 336 3873 | General information |
| +90 540 336 3873 | Measurement record, visual and video sharing | |
| info@pliseperde.com | Official requests and written confirmations | |
| Address | Esenyalı Mah. Edebali Cad. No:13/C, 34903 Pendik/Istanbul | Written notifications |
20. Our Social Media Accounts
Social media accounts may be used for promotion and information purposes. Final measurements must be confirmed with written order record. Production changes are not finalized with social media messages. Official notifications must be made via suitable channels.
- Facebook: facebook.com/FenetreSystems
- Instagram: instagram.com/fenetresystems
- X: x.com/fenetresystems
- YouTube: youtube.com/@FenetreSystems
- Pinterest: tr.pinterest.com/fenetresystems
- LinkedIn: linkedin.com/company/fenetresystems
21. Relationship with Other Information Texts
This information is applied together with other policies and contracts. In case of conflict, mandatory legislation provisions are the basis. Written records specific to order are also taken into account. Technical guidances are complementary in nature.
- Order and Custom Production Terms
- Distance Sales Contract
- Preliminary Information Form
- Mounting and Application Terms
- Return, Exchange and Withdrawal Right Policy
- Warranty and After-Sales Support Policy
- Delivery and Shipping Policy
- Privacy Policy
- KVKK Illumination Text
22. Entry into Force and Updates of the Text
This Measurement Information enters into force on June 12, 2026. Technical methods may be updated according to product series. Operational arrangements may be reflected in the text. Current version is published on the website.
Version in force on order date is taken into account for the relevant transaction. Customer must examine the current text before production approval. Confirmation records specific to order are also the basis. Current record is preserved.
| Document Information | Value |
|---|---|
| Document Name | Measurement Information |
| Brand | Pleated Blind |
| Entry into Force Date | June 12, 2026 |
| Version | 1.0 |
| Contact | info@pliseperde.com |